<html><body style="word-wrap: break-word; -webkit-nbsp-mode: space; -webkit-line-break: after-white-space; ">Did you look at the make file in the posting i did on this?<div>I am using avrdude which you may try to see if is an avr studio issue.</div><div><br></div><div><a href="http://www.dorkbotpdx.org/blog/feurig/burning_a_bootloader_with_the_avr_dragon">http://www.dorkbotpdx.org/blog/feurig/burning_a_bootloader_with_the_avr_dragon</a></div><div><br></div><div>Don</div><div><br><div><div>On Jun 9, 2009, at 1:17 PM, Hans Lindauer wrote:</div><br class="Apple-interchange-newline"><blockquote type="cite"> <div bgcolor="#ffffff" text="#000000"> I tried the whole meeting last night to get my Dragon to burn Adaboot onto an ATmega168 using ISP, but didn't have any luck. I think I can rule out Vista as the culprit, because it does the same thing on XP at home.<br> <br> Has anyone had any luck with this setup?<br> <br> Here's what I did:<br> <ul> <li>Wired the Dragon as per <a href="http://support.atmel.no/knowledgebase/avrstudiohelp/mergedProjects/AVRDragon/SCKT3200A2.htm">http://support.atmel.no/knowledgebase/avrstudiohelp/mergedProjects/AVRDragon/SCKT3200A2.htm</a> and socketed the chip<br> </li> <li>In AVR Stuidio: connected to the Dragon on the USB port</li> <li>Left ISP Frequency at 1.000 MHz</li> <li>Selected ADABoot_168.hex from <!-- <a href="http://www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip"> --><!-- <a href="http://www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip"> -->http://www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip
<font color=gray>[ www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip ]</font> <!-- </a> --> <font color="gray">[ <!-- <a href="http://www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip"> -->www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip
<font color=gray>[ www.wulfden.org/downloads/code/arduino/ADABootLoaderR3_9D15.zip ]</font> <!-- </a> --> ]</font> <!-- </a> --> as my Flash Input HEX File</li> <li>Set low_fuses=0xff, high_fuses=0xdd, extended_fuses=0x00 as per append_2_boards.txt (from above archive)</li> <li>Set lockbit to 0x0f (per above), this one I'm not sure about at all</li> <li>Left all other parameters to default<br> </li> <li>When I program the chip, I get the following messages and also an ISP Mode Error message popup.<br> </li> <ul> <li>Getting ISP frequency parameters.. SD=0x03 .. OKOK<br> Reading FLASH input file.. OK<br> Setting device parameters.. OK!<br> Entering programming mode.. FAILED!<br> Leaving programming mode.. OK!<br> </li> </ul> </ul> Can someone please point me in the right direction here? I tried all of the lower ISP frequency settings. Also, I get the same errors if I try to erase the device.<br> <br> Thanks,<br> -Hans<br> </div> _______________________________________________<br>dorkbotpdx-blabber mailing list<br><a href="mailto:dorkbotpdx-blabber@dorkbot.org">dorkbotpdx-blabber@dorkbot.org</a><br><a href="http://music.columbia.edu/mailman/listinfo/dorkbotpdx-blabber">http://music.columbia.edu/mailman/listinfo/dorkbotpdx-blabber</a></blockquote></div><br></div></body></html>